Induction Hob Fault Finding

Induction hob no longer working, or having problems getting it to come on? Discover the various possible causes of this issue with the help of this troubleshooting guide.

Induction Hob Fault Finding Nemo

THE POSSIBLE CAUSES FOR THIS FAULT:

WARNING
Before you do anything to your appliance, make sure you disconnect it from the power supply.
Once upon a december letter notes. There is a risk of electric shock.
Wear suitable protective gloves if you need to dismantle anything.
There is a risk of getting cut or injured

Induction Hob Installation Faults. Last updated 09:00 Issue. The appliance cannot be activated / is not operating; Only two cooking zones are operating. Customer sent to me the Taiko brand induction cooker for repair and the complaint was no power. If you want to fix any electronic equipment, first you need to understand how the equipment work. You may refer to other brand of induction cooker block or schematic diagram if you can’t find the exact information of your model. Hopefully, if you've come into contact with a common ceramic hob fault, this advice will do the trick: My ceramic hob won't turn on. If your ceramic hob won't turn on it's very likely that you have a faulty hob element. This is the part of your cooker that heats up your ceramic hob so if it becomes faulty it's important that you replace it. Induction fault stuart mcgill. Unsubscribe from stuart mcgill? Miele Induction Hobs with TempControl Miele - Duration: 0:58. Miele UAE 5,092 views. NZ3000 Induction Hob. Samsung Support UK.

There is a problem with the electrical installation

One of the first things to check is the power supply: is the hob properly plugged in/connected at the socket? Are the terminal connectors, if there are any, properly tightened? Is there definitely current flowing? You can test the socket with a multimeter in voltmeter mode (AC). Place the two probes of the meter on the socket terminals or the terminal connectors (if there are any). You should get a reading of around 230 volts.

The terminal block on the hob is damaged

The terminal block can get damaged or burnt out, preventing the hob from switching on. This is often caused by a loosely tightened screw or a badly connected earth wire (the green and yellow one). Check the condition of the terminal block (located on the back of the hob), and replace it if it's in too damaged a condition.

The cables on the terminal block are not properly connected

If you have a cooker and the oven works fine but your induction hob doesn't, it is essential to check that the screws on the terminal block are properly tightened. Most terminal blocks have several connection points. These serve to route the electricity to both the oven and the hob. If the wires are not properly connected, or if any are connected in the wrong place, part of the appliance may not work. The same issue can arise on an induction hob: if part of the hob is not working, check the terminal block.

The power board is defective

The circuit board manages all your hob's functions. If you have already carried out all the checks detailed above and your hob still won't come on, it may be the circuit board that's causing the problem, in which case it will need to be replaced. As this is a complex and expensive step to take, if you are not confident that you have diagnosed the problem correctly, contact our technical service or seek the help and advice of a manufacturer-approved engineer.

Know more about us

Failure signs

Refrigeration
Laundry
Dishwashers
Cooking
Built-In
Small Appliances

If you have a cooker with an induction hob, you will need to use induction compatible pans for it to work. These are often identified with the induction symbol. You can also test compatibility by using a magnet on the bottom of the saucepan - if it clings onto it, then it should work with an induction hob. In addition to this, always make sure the whole of the heating surface is covered by the pan.

Thank you for your feedback

We are so sorry we were unable to answer your question. You might be able to find the answer you are looking for in the ‘Related Questions’ below.We are always looking to improve our service so would really appreciate your feedback on why we were unable to help you today.After you have completed your feedback please head over to our Contact Us page for further assistance as we are unable to respond directly to your feedback.